252 lines
6.0 KiB
Plaintext
252 lines
6.0 KiB
Plaintext
// SPDX-License-Identifier: ISC
|
|
/*
|
|
* Device Tree file for the USRobotics USR8200 firewall
|
|
* VPN and NAS. Based on know-how from Peter Denison.
|
|
*
|
|
* This machine is based on IXP422, the USR internal codename
|
|
* is "Jeeves".
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "intel-ixp42x.dtsi"
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "USRobotics USR8200";
|
|
compatible = "usr,usr8200", "intel,ixp42x";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x4000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
stdout-path = "uart1:115200n8";
|
|
};
|
|
|
|
aliases {
|
|
/* These are switched around */
|
|
serial0 = &uart1;
|
|
serial1 = &uart0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
ieee1394_led: led-1394 {
|
|
label = "usr8200:green:1394";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
usb1_led: led-usb1 {
|
|
label = "usr8200:green:usb1";
|
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
usb2_led: led-usb2 {
|
|
label = "usr8200:green:usb2";
|
|
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
wireless_led: led-wireless {
|
|
/*
|
|
* This LED is mounted inside the case but cannot be
|
|
* seen from the outside: probably USR planned at one
|
|
* point for the device to have a wireless card, then
|
|
* changed their mind and didn't mount it, leaving the
|
|
* LED in place.
|
|
*/
|
|
label = "usr8200:green:wireless";
|
|
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
|
default-state = "off";
|
|
};
|
|
pwr_led: led-pwr {
|
|
label = "usr8200:green:pwr";
|
|
gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
|
|
button-reset {
|
|
wakeup-source;
|
|
linux,code = <KEY_RESTART>;
|
|
label = "reset";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
soc {
|
|
bus@c4000000 {
|
|
flash@0,0 {
|
|
compatible = "intel,ixp4xx-flash", "cfi-flash";
|
|
bank-width = <2>;
|
|
/* Enable writes on the expansion bus */
|
|
intel,ixp4xx-eb-write-enable = <1>;
|
|
/* 16 MB of Flash mapped in at CS0 */
|
|
reg = <0 0x00000000 0x1000000>;
|
|
|
|
partitions {
|
|
compatible = "redboot-fis";
|
|
/* Eraseblock at 0x0fe0000 */
|
|
fis-index-block = <0x7f>;
|
|
};
|
|
};
|
|
rtc@2,0 {
|
|
/* EPSON RTC7301 DG DIL-capsule */
|
|
compatible = "epson,rtc7301dg";
|
|
/*
|
|
* These timing settings were found in the boardfile patch:
|
|
* IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN |
|
|
* IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN;
|
|
*/
|
|
intel,ixp4xx-eb-t1 = <0>; // no cycles extra address phase
|
|
intel,ixp4xx-eb-t2 = <0>; // no cycles extra setup phase
|
|
intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
|
|
intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
|
|
intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
|
|
intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle
|
|
intel,ixp4xx-eb-byte-access-on-halfword = <0>;
|
|
intel,ixp4xx-eb-mux-address-and-data = <0>;
|
|
intel,ixp4xx-eb-ahb-split-transfers = <0>;
|
|
intel,ixp4xx-eb-write-enable = <1>;
|
|
intel,ixp4xx-eb-byte-access = <1>;
|
|
/* 512 bytes at CS2 */
|
|
reg = <2 0x00000000 0x0000200>;
|
|
reg-io-width = <1>;
|
|
native-endian;
|
|
/* FIXME: try to check if there is an IRQ for the RTC? */
|
|
};
|
|
};
|
|
|
|
pci@c0000000 {
|
|
status = "okay";
|
|
|
|
/*
|
|
* Taken from USR8200 boardfile from OpenWrt
|
|
*
|
|
* We have 3 slots (IDSEL) with partly swizzled IRQs on slot 16.
|
|
* We assume the same IRQ for all pins on the remaining slots, that
|
|
* is what the boardfile was doing.
|
|
*/
|
|
#interrupt-cells = <1>;
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map =
|
|
/* IDSEL 14 used for "Wireless" in the board file */
|
|
<0x7000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */
|
|
/* IDSEL 15 used for VIA VT6307 IEEE 1394 Firewire */
|
|
<0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 8 */
|
|
/* IDSEL 16 used for VIA VT6202 USB 2.0 4+1 */
|
|
<0x8000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 16 is irq 11 */
|
|
<0x8000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 16 is irq 10 */
|
|
<0x8000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 16 is irq 9 */
|
|
};
|
|
|
|
gpio@c8004000 {
|
|
/* Enable clock out on GPIO 15 */
|
|
intel,ixp4xx-gpio15-clkout;
|
|
};
|
|
|
|
/* EthB WAN */
|
|
ethernet@c8009000 {
|
|
status = "okay";
|
|
queue-rx = <&qmgr 3>;
|
|
queue-txready = <&qmgr 20>;
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy9>;
|
|
|
|
mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
/*
|
|
* PHY 0..4 are internal to the MV88E6060 switch but appear
|
|
* as independent devices.
|
|
*/
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
phy1: ethernet-phy@1 {
|
|
reg = <1>;
|
|
};
|
|
phy2: ethernet-phy@2 {
|
|
reg = <2>;
|
|
};
|
|
phy3: ethernet-phy@3 {
|
|
reg = <3>;
|
|
};
|
|
|
|
/* Altima AMI101L used by the WAN port */
|
|
phy9: ethernet-phy@9 {
|
|
reg = <9>;
|
|
};
|
|
|
|
/* The switch uses MDIO addresses 16 thru 31 */
|
|
switch@16 {
|
|
compatible = "marvell,mv88e6060";
|
|
reg = <16>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
label = "lan1";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
label = "lan2";
|
|
phy-handle = <&phy1>;
|
|
};
|
|
|
|
port@2 {
|
|
reg = <2>;
|
|
label = "lan3";
|
|
phy-handle = <&phy2>;
|
|
};
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
label = "lan4";
|
|
phy-handle = <&phy3>;
|
|
};
|
|
|
|
port@5 {
|
|
/* Port 5 is the CPU port according to the MV88E6060 datasheet */
|
|
reg = <5>;
|
|
phy-mode = "rgmii-id";
|
|
ethernet = <ðc>;
|
|
label = "cpu";
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
/* EthC LAN connected to the Marvell DSA Switch */
|
|
ethc: ethernet@c800a000 {
|
|
status = "okay";
|
|
queue-rx = <&qmgr 4>;
|
|
queue-txready = <&qmgr 21>;
|
|
phy-mode = "rgmii";
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|