59 lines
1.3 KiB
Plaintext
59 lines
1.3 KiB
Plaintext
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||
|
|
/*
|
||
|
|
* Copyright (c) 2021 SUSE LLC
|
||
|
|
* Copyright 2019-2021, 2024 NXP
|
||
|
|
*/
|
||
|
|
|
||
|
|
/dts-v1/;
|
||
|
|
|
||
|
|
#include "s32g2.dtsi"
|
||
|
|
|
||
|
|
/ {
|
||
|
|
model = "NXP S32G2 Reference Design Board 2 (S32G-VNP-RDB2)";
|
||
|
|
compatible = "nxp,s32g274a-rdb2", "nxp,s32g2";
|
||
|
|
|
||
|
|
aliases {
|
||
|
|
serial0 = &uart0;
|
||
|
|
serial1 = &uart1;
|
||
|
|
};
|
||
|
|
|
||
|
|
chosen {
|
||
|
|
stdout-path = "serial0:115200n8";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* 4GiB RAM */
|
||
|
|
memory@80000000 {
|
||
|
|
device_type = "memory";
|
||
|
|
reg = <0x0 0x80000000 0 0x80000000>,
|
||
|
|
<0x8 0x80000000 0 0x80000000>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* UART (J2) to Micro USB port */
|
||
|
|
&uart0 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* UART (J1) to Micro USB port */
|
||
|
|
&uart1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&usdhc0 {
|
||
|
|
pinctrl-names = "default", "state_100mhz", "state_200mhz";
|
||
|
|
pinctrl-0 = <&pinctrl_usdhc0>;
|
||
|
|
pinctrl-1 = <&pinctrl_usdhc0_100mhz>;
|
||
|
|
pinctrl-2 = <&pinctrl_usdhc0_200mhz>;
|
||
|
|
disable-wp;
|
||
|
|
/* Remove no-1-8-v to enable higher speed modes for SD card.
|
||
|
|
* However, this is not enough to enable HS400 or HS200 modes for eMMC.
|
||
|
|
* In this case, the position of the resistor R797 must be changed
|
||
|
|
* from A to B before removing the property.
|
||
|
|
* If the property is removed without changing the resistor position,
|
||
|
|
* HS*00 may be enabled, but the interface might be unstable because of
|
||
|
|
* the wrong VCCQ voltage applied to the eMMC.
|
||
|
|
*/
|
||
|
|
no-1-8-v;
|
||
|
|
status = "okay";
|
||
|
|
};
|